Why does my form go completely blank?

        4 votes: *****      6,498 views      0 comments
by Allen Browne, 05 September 2006    (All versions of Access)

Microsoft Access Tips for Casual Users

Provided by Allen Browne, August 2006


Why does my form go completely blank?

The entire Detail section of a Microsoft Access form goes blank sometimes. The text boxes you see in design view disappear when you go to use the form, leaving nothing but empty space.

The Cause

It happens when both these conditions are met:

  1. There are no records to display, and
  2. No new records can be added.

Condition (a) can be triggered in several ways. Examples:

  • The form's Data Entry property is set to Yes. (This means the form shows no existing records, i.e. it is for entering new ones only.)
  • The form has a Filter applied (or is opened with a WhereCondition) that yields no records.
  • The form is based on a query where the criteria yield no records.
  • The form is based on a table that has no records.

Condition (b) can be also be triggered by several things:

  • The form's Allow Additions property is set to No.
  • The form's Recordset Type property is set to something other than Dynaset.
  • The form is based on a read-only query. (If you cannot add a record directly to your query, see Why is my query read-only?)

You can demonstrate the problem with any form, just by setting its Data Entry property to Yes, and Allow Additions to No.

If it has Form Header and Form Footer sections, controls in these sections will still be visible but they may not work properly. (This is one of the issues discussed in Incorrect display of data.)

Workarounds

You cannot prevent this from happening, unless you can avoid (a) and (b) being true at the same time.

If you have set Allow Additions to No so as to prevent new records, there is a simple workaround. Set Allow Additions back to Yes, so the form can show the new record when there are no others. You can prevent new records by canceling the BeforeInsert event of the form. Steps:

  1. Set the Before Insert property of the form to:    [Event Procedure]
  2. Click the Build button (...) beside this. Access opens the code window.
  3. Insert the line Cancel = True between the other two. The code will look like this:
        Private Sub Form_BeforeInsert(Cancel As Integer)
            Cancel = True
        End Sub

If you cannot prevent condition (b), you might be able to prevent condition (a). For example, if you are opening a form with a WhereCondition that could result in no records, you might prefer to display a dialog rather than the blank form. To do that, cancel the Open event of the form:

Private Sub Form_Open(Cancel As Integer)
    If Me.RecordsetClone.RecordCount = 0 Then
        Cancel = True
        MsgBox "No records"
    End If
End Sub

(Note: The procedure where you used OpenForm will be notified with error 2501 that the form did not open. Use error handling in that procedure to trap the message.)

There are times when you cannot prevent (a) and (b) happening together. A complex search form may have to use a read-only query, and the user's criteria may return no results. For these cases, place the criteria boxes in the form header section, and accept the fact that users will be okay if they see nothing when the search returns no results.


HomeIndex of tipsTop

Rate this article:   Your rating: Poor Your rating: Not so good Your rating: Average Your rating: Good Your rating: Excellent


This is a cached tutorial, reproduced with permission.

Have your say - comment on this article.

What did you think of 'Why does my form go completely blank?'?

No comments yet.

Why not be the first to comment on this article?!

Have your say...

Name
E-mail (e-mail address will be kept private)
Comments
Verify Code
Verification Code


It may take 30 seconds after clicking submit - please be patient to avoid duplicate submissions.  

All comments must be approved before being displayed on this web page.  This process may take up to 24 hours.